Flat Tow Setup on 4th Gen Tacoma Done

[jkcerruti]

@Leo319 Thank you for the diode kit, I ordered that. I'm sorry to be a pest, but I was wondering if you had your measurements for your driveshaft, or your worksheet handy. I believe it's SKU-3, and my measurements were: 71.1875" long, and the caps are 1.125". does that seem similar to yours? I left Bill a message this morning but I haven't heard back from him. My next step will be an email.

Also random, but I'm in Santa Cruz, I see you're in the Monterey Bay Area.

Sponsored

 

[Leo319]

@Leo319 Thank you for the diode kit, I ordered that. I'm sorry to be a pest, but I was wondering if you had your measurements for your driveshaft, or your worksheet handy. I believe it's SKU-3, and my measurements were: 71.1875" long, and the caps are 1.125". does that seem similar to yours? I left Bill a message this morning but I haven't heard back from him. My next step will be an email.

Also random, but I'm in Santa Cruz, I see you're in the Monterey Bay Area.

Oh snap! Small world, I’ll look for it and send you a PM. Not a big deal. Sucks that theres not a lot of info on tacomas. I’ve struggled with this since the last gen. I’m in LA for the week, I’ll be back next week and send you those measurements.

 

[Leo319]

Oh snap! Small world, I’ll look for it and send you a PM. Not a big deal. Sucks that theres not a lot of info on tacomas. I’ve struggled with this since the last gen. I’m in LA for the week, I’ll be back next week and send you those measurements.

Actually just got this on my sent emails.

71” 1/16th for SKU 3

 

[jkcerruti]

Actually just got this on my sent emails.

71” 1/16th for SKU 3

Awesome! Thank you!

 

[jkcerruti]

@Leo319 Thank you for your assistance with the parts. I ended up ordering and installing:

Roadmaster RM32EQ Direct Connect base plate kit for 2024 Toyota Tacoma: which ended up needing some modification to the bolt holes that go into the stock tow hook mounts. fit perfectly in the slots in the air dam, or you can leave the air dam off. On my limited I had to order .75" rubber plugs for the control arms to eliminate the wind howl by removing the air dam.

Demco Stay-In-Play Duo braking system (this fit perfectly). The 6 pin plug, and break away switch fit perfectly in the lower grill with no modifications.

Roadmaster Smart Diode Kit for Variable Voltage LED: RM38FR: I ran the wiring down the passenger side frame rail and I ended up with 1 foot extra by the time I reached the passenger tail light. I happened to have extra to run across the back to the drivers side tail light, but order extra if you're doing a fresh installation.

Remco Driveline Disconnect: I tried to order in aluminum to match stock, but they can only make out of steel. It's being built now.

I will update when the driveline arrives!

 

[Leo319]

@Leo319 Thank you for your assistance with the parts. I ended up ordering and installing:

Roadmaster RM32EQ Direct Connect base plate kit for 2024 Toyota Tacoma: which ended up needing some modification to the bolt holes that go into the stock tow hook mounts. fit perfectly in the slots in the air dam, or you can leave the air dam off. On my limited I had to order .75" rubber plugs for the control arms to eliminate the wind howl by removing the air dam.

Demco Stay-In-Play Duo braking system (this fit perfectly). The 6 pin plug, and break away switch fit perfectly in the lower grill with no modifications.

Roadmaster Smart Diode Kit for Variable Voltage LED: RM38FR: I ran the wiring down the passenger side frame rail and I ended up with 1 foot extra by the time I reached the passenger tail light. I happened to have extra to run across the back to the drivers side tail light, but order extra if you're doing a fresh installation.

Remco Driveline Disconnect: I tried to order in aluminum to match stock, but they can only make out of steel. It's being built now.

I will update when the driveline arrives!

That’s awesome! They didn’t have the baseplate available when I did my set up, post a pic once installed if you don’t mind. Curious to see how it comes out.

I had a few folks reaching out on this forum and Dynamax group, glad this thread is helping others.

Hey not sure if I mentioned it, but make sure you deactivate the automatic parking brake on the Tacoma. That will make a mess if left on. I got used to it before I installed everything, but I can see people forgetting about it unless they’re towing frequently.

 

[Mike5]

A little off topic, but check out the NSARV Products tow bar with built in surge brake. I ended up going with that. Very well made and a great warranty.

Sponsored