Sponsored

lets.go.overlandon

TRD Off-Road Premium
New member
First Name
Landon
Joined
Jan 28, 2025
Threads
0
Messages
4
Reaction score
8
Location
Denver, Colorado
Vehicle(s)
2024 Tacoma TRD Off-Road Premium
Finally got around to installing my Midland MXT275 GMRS radio!

I wanted to go as stealth as possible with this install so I put the radio in the itself in the console and ran the handset connection to an RJ 45 port I got from Ebay.

2024 Tacoma HAM and GMRS Radio Installs in 4th gen Tacoma -- Post Your Setups IMG_7740
2024 Tacoma HAM and GMRS Radio Installs in 4th gen Tacoma -- Post Your Setups IMG_7741
2024 Tacoma HAM and GMRS Radio Installs in 4th gen Tacoma -- Post Your Setups IMG_7742
2024 Tacoma HAM and GMRS Radio Installs in 4th gen Tacoma -- Post Your Setups IMG_7743


The console was fairly easy to remove. I found this video that walks through the process in detail.

For the mic port in the console, I used this RJ45 port and it popped in beautifully! Since the mic is the controls for the radio itself I can just keep it in the console until I want to use it.

For power to the radio, I went directly to the battery but since I have the iForce Max, the battery is in the cab under the rear seat. It was pretty easy to fish the power under the carpet and then to the terminals of the battery.
Sponsored

 

SirLeigh

Trailhunter
Active member
Joined
Mar 27, 2025
Threads
6
Messages
37
Reaction score
12
Location
North Carolina
Vehicle(s)
2025 Tacoma Trailhunter
Finally got around to installing my Midland MXT275 GMRS radio!

I wanted to go as stealth as possible with this install so I put the radio in the itself in the console and ran the handset connection to an RJ 45 port I got from Ebay.

IMG_7740.jpg
IMG_7741.jpg
IMG_7742.jpg
IMG_7743.jpg


The console was fairly easy to remove. I found this video that walks through the process in detail.

For the mic port in the console, I used this RJ45 port and it popped in beautifully! Since the mic is the controls for the radio itself I can just keep it in the console until I want to use it.

For power to the radio, I went directly to the battery but since I have the iForce Max, the battery is in the cab under the rear seat. It was pretty easy to fish the power under the carpet and then to the terminals of the battery.
How much of a pain was it to wire the antenna from there? Did you go through the center console and into the engine bay for it?
 
OP
OP
Romer

Romer

TRD Off-Road Premium
Well-known member
First Name
Ken
Joined
Mar 11, 2024
Threads
19
Messages
181
Reaction score
190
Location
Centennial, CO
Vehicle(s)
2024 Tacoma Off Road & 2014 Land Cruiser
Nice install!

Curious is there is room for the main unit under the center console below where you put the RJ45 connector.
 
Last edited:

lets.go.overlandon

TRD Off-Road Premium
New member
First Name
Landon
Joined
Jan 28, 2025
Threads
0
Messages
4
Reaction score
8
Location
Denver, Colorado
Vehicle(s)
2024 Tacoma TRD Off-Road Premium
How much of a pain was it to wire the antenna from there? Did you go through the center console and into the engine bay for it?
Not too difficult. Just ran the wire through the firewall grommet and then routed it towards the front of the dash at the bottom. Then with the center console removed it was very easy to fish it through the gear shift tunnel. I just ziptied it in a couple of places to ensure that it wasn't going to be near the pedals or the gearshift itself. I can add some photos in a bit!
 

lets.go.overlandon

TRD Off-Road Premium
New member
First Name
Landon
Joined
Jan 28, 2025
Threads
0
Messages
4
Reaction score
8
Location
Denver, Colorado
Vehicle(s)
2024 Tacoma TRD Off-Road Premium
Nice install!

Curious is there is room for the main unit under the center console below where you put the RJ45 connector.
I don't think you could really fit it in there. It's a bit of a tight space and there's really nothing to mount it to in there. You could likely fashion a way to mount it in the rear storage/battery compartment though.
 

Sponsored

davisjm0311

TRD Pro
New member
First Name
John
Joined
Dec 2, 2024
Threads
0
Messages
3
Reaction score
2
Location
Arnold, MO
Vehicle(s)
2024 Tacoma TRD Pro
Finally got around to installing my Midland MXT275 GMRS radio!

I wanted to go as stealth as possible with this install so I put the radio in the itself in the console and ran the handset connection to an RJ 45 port I got from Ebay.

IMG_7740.jpg
IMG_7741.jpg
IMG_7742.jpg
IMG_7743.jpg


The console was fairly easy to remove. I found this video that walks through the process in detail.

For the mic port in the console, I used this RJ45 port and it popped in beautifully! Since the mic is the controls for the radio itself I can just keep it in the console until I want to use it.

For power to the radio, I went directly to the battery but since I have the iForce Max, the battery is in the cab under the rear seat. It was pretty easy to fish the power under the carpet and then to the terminals of the battery.
That’s an awesome setup!

I just picked up a MXT575, and I think I’m going to do something similar.
How/where did you mount the clip for the mic? It looks like you have it on the grab bar maybe?
 

Hammer

TRD Sport
New member
Joined
Apr 24, 2025
Threads
0
Messages
1
Reaction score
0
Location
Atlanta
Vehicle(s)
24 Taco
Has anyone done an HF install yet? If so, what did you do about the RFI? I’ve thrown everything I can think of and find at it with no luck. Bonded it to no end, ferrites and noise filters on coax and power, different antenna locations, the whole deal. Best I can do is knock it down a few S levels but its still insanely loud.
Sponsored

 
 






Top