ARB Compressor Mounts

[Romer]

I have been rfesearching ARB Compressor mounts. I know I have the option to buy a portable compressor, this thread is about mounts. I thought about the dual ARB with Tank in a case, but that takes up space although more mobile. I don't really need the mobility since I have a dual ARB in the Land Cruiser.

So thinking a single ARB or Dual ARB.
There is a member on this forum who 3D printed a single ARB mount bracket that goes in the small empty space. That is really cool and innovative. I am surprised no vender has developed a bracket for that open space in the driver front engine bay. Maybe some are coming.
https://www.tacoma4g.com/forum/thre...ing-custom-bracket-3d-print-file-inside.6050/

There is this company that has a Dual ARB mount in the engine bay, but you have to move the ECU and am concerned that would void the warranty besides concerns about changing the dynamics it wwas tested to. Anyone try this? Comments on warranty or modifications? I think what they did looks well designed.


Then there are several that mount it above the spare tire bracket. That would leave it exposed to the elements. Is that something I should worry about
https://sdhqoffroad.com/products/sd...EIfokp7iBL9JG6T37naqYidOrmvUgRvAzNajdMB61QLLi

or I wait and see what else comes about


Anyone see other mounts or have comments on these?

Sponsored

 

[Sagebrush]

I’m the guy that developed the 3D printed mount. It’s still doing fine with 3700 miles on it and a fair amount of that is on rough washboard roads.

I’m pleased with it.

 

[Romer]

I’m the guy that developed the 3D printed mount. It’s still doing fine with 3700 miles on it and a fair amount of that is on rough washboard roads.

I’m pleased with it.

You did a real nice job on that. Thankss for sharing it

 

[PotatoTRD]

I mounted my arb twin In the bed similar to the trailhunter. I mounted with the filters facing upward in hopes of cleaner air, but I only anticipate using it while parked so it shouldn’t be an issue.

 

[Romer]

Pretty cool. How easy is it to get the panels off to mount the compressor

 

[Pootklopp]

I mounted my arb twin In the bed similar to the trailhunter. I mounted with the filters facing upward in hopes of cleaner air, but I only anticipate using it while parked so it shouldn’t be an issue.

Can you give some more info on this install? I'm thinking this will be my preferred solution. Is it on the rear aux switch? How did you power the unit? Long connection straight to the battery? Is that a specific mounting plate?

 

[PotatoTRD]

Pretty cool. How easy is it to get the panels off to mount the compressor

The only panel I had to remove was the accessory 12v power panel. Other than that I just lifted it up to the bedside the the opening I think if you have the factory exhaust it might be tricky to get it in there, but I have the trailhunter tailpipe.

 

[PotatoTRD]

Can you give some more info on this install? I'm thinking this will be my preferred solution. Is it on the rear aux switch? How did you power the unit? Long connection straight to the battery? Is that a specific mounting plate?

The rear aux switch has no where near enough power for the dual compressor, the rear aux is for 20amp and the dual compressor needs around 80amps (40 for each compressor). I have the hybrid so my run for wiring was only to the rear seat area and I had to extend the arb power harness like a foot or so. As for the bracket I found it on a bronco site, it’s for mounting a dual compressor to a molle panel but it worked perfect for my application. I don’t think the bracket is 100% needed but it added a little piece of mind for me. It also served as a template for drilling holes in the bedside.

Sponsored