What did you do TO / WITH your 4th gen Tacoma today?! 👨‍🏭 🧰 📸

[oldskoolarcher]

Got my SXTH Element CPLT Intake today, and installed it.

Thoughts?

Sponsored

 

[Bravada]

Thoughts?

It compliments the AWE exhaust perfectly, and sets me up for Overland Tailor Tuning.

 

[JD11]

It compliments the AWE exhaust perfectly, and sets me up for Overland Tailor Tuning.

Do you have a video of the exhaust/intake combo sound? I am looking at those 2 upgrades along with the OTT tune so curious what it would be like.

 

[Bravada]

Do you have a video of the exhaust/intake combo sound? I am looking at those 2 upgrades along with the OTT tune so curious what it would be like.

I did make a video, but when I try and upload it, there is no sound. It must be an Apple .MOV issue. I'll try and use my wifes Android later.

 

[Bravada]

I did make a video, but when I try and upload it, there is no sound. It must be an Apple .MOV issue. I'll try and use my wifes Android later.

Do you have a video of the exhaust/intake combo sound? I am looking at those 2 upgrades along with the OTT tune so curious what it would be like.

Bluetooth was the culprit, my phone was evidently pairing with the truck and killing the audio. Here you go. The rear exhaust video was on high idle, the intake video was after the it went off high idle. Not professional level audio recording, it sounds much better in person.

 

[JD11]

Bluetooth was the culprit, my phone was evidently pairing with the truck and killing the audio. Here you go. The rear exhaust video was on high idle, the intake video was after the it went off high idle. Not professional level audio recording, it sounds much better in person.

Appreciate you! I think AWE nailed it with this. I’ve heard others say it’s pretty minimal droning and not too obnoxious driving around town. And 100% sound better in person, just need to find someone who lives around me with one so I can just pull the trigger on it. Thanks!

 

[SnowmanJPS]

Finally cut the mat, and installed the OEM hard tri fold drain tubes very happy with these versatrax anchors

 

[MHG]

Made my off-road more TRDY. Skid plate, recovery points, wheel well liners. Hi-lift jack mounts.

 

[TX-BluStreak]

Your rail end caps are stuck on with the spray-on bedliner? Or the tie downs on the floor of the bed? When I installed my front bed Molle panel, I had to take a razor and a pick to get the bolts out of the bed floor. I cut carefully around the bolts, and used the pick to dig out the bed liner from around and in the head of the bolt, so I could get the bit in the bolt.

Since I went in to get my Cast Aluminum Running Boards installed today at the dealership; I was able to get them to remove them for me (at no charge). Appreciate the helpful suggestions.

 

[SonoranSurvivalist]

Got my Westscott Designs rock rails... took a few hours of time to install. The threaded rivets where an absolute bitch to install.

 

[MT-Taco]

Bath day…. Finally!

 

[Bravada]

Got my Westscott Designs rock rails... took a few hours of time to install. The threaded rivets where an absolute bitch to install.

On the plus side, your misery has an awesome result!

 

[jettaway]

Installed the ARB twin air compressor in the bed at the same location the OEM one mounts. Created a custom solution for the switch and Air chuck.

So far this has been a welcome addition. And the Twin ARB really puts our air.

 

[Bravada]

I couldn't wait another 80 miles to do the first oil change at 1K miles. Not sure I'm going to baby it for another 80 miles either. Add me to the gorilla put on the oil filter at the factory club.

 

[Bravada]

Installed the ARB twin air compressor in the bed at the same location the OEM one mounts. Created a custom solution for the switch and Air chuck.

So far this has been a welcome addition. And the Twin ARB really puts our air.

I would love to know more, I'm interested in that mod.

Sponsored